FraMCoS 11

This text briefly introduces the content in the page.

Fatigue damage versus creep deformation – differentiation using the development of stiffness

Concrete structures, especially bridges, can exhibit deformations due to creep, induced by cyclic loading at serviceability limit state. These deformations can exceed the deformation when static creep is considered. For loading levels corresponding to serviceability stress-levels, structural damage in terms of micro-cracking is not supposed to occur. In contrast, in fatigue testing viscous deformations (without

Multi-physics simulation of corrosion-induced cracking of concrete by means of a mesoscopic modeling approach

Corrosion-induced cracking is a deterioration problem. It endangers the durability of con- creteinfrastructure. It is a multi-physics process whichincludesthetransportofchemicallyaggressive ions from the surface of a reinforced concrete structure, through the mesostructure of concrete, to the steel rebars. Corrosion results in a volume expansion of steel. The corresponding development of ten- sile stresses of the concrete

Behavior of post-installed anchors under tensile fatigue loading

Post-installed anchors are rigorously used in structures such as factory buildings, tunnels, and highway bridges to connect structural and non-structural elements, and are subjected to fatigue loading during service period. The investigation on fatigue behavior of post-installed anchors has been, however, limited up to now. In this paper, the fatigue behavior of post-installed mechanical expansion

Phase-field model for degradation of steel fiber-reinforced ultra-high performance concrete during low cycle fatigue

The degradation of fiber-reinforced ultra-high performance concrete (UHPC) is mainly dominated by the pseudo-ductile behavior of concrete material and the complex fiber-matrix inter- actions. A phenomenological material model is derived, which is a combination of the superposed models of one-dimensional elasto-plasticity to describe the fibers and an elasto-plastic phase-field modeloffracture in concrete material. Therein, to

Residual capacity of fatigue-prone reinforced concrete structures

Designing reinforced concrete structures susceptible to fatigue damage requires satisfying the fatigue limit state. Current codes’ stress-life curve considerations are confined to the design stages and cannot be used to monitor evolving fatigue damage if the structure in service is subjected to severe environmental conditions or loads that are higher than the design values. One

Fracture behavior and its influence on the shear capacity of high-strength reinforced concrete beams with recycled concrete aggregate

The fracture and shear responses of the concrete with natural coarse aggregate (NCA) and recycled coarse aggregate (RCA) are evaluated. There is a 25 % reduction in the compressive strength of concrete proportioned for 50 MPa characteristic strength in replacing NCA with RCA. The corresponding tensile strength is less sensitive, with a 9% decrease. The

3action: a viable setup for direct-tensile testing of concrete

The experimental characterization of concrete’s post-peak stress vs crack opening curve is a key aspect in many practical problems involving crack stability, like size-effect and explosive spalling of High-Performance concrete in the fire. The direct-tension test is recognized as the most straightforward solution, though the strain-softening material behaviour entails tricky issues concerning the axial and

A comparative study of implicit and explicit solution procedures for computational modeling of reinforced concrete structures

This paper presents a systematic comparison between implicit and explicit solution procedures for simulating the fracture processes in reinforced concrete. Implicit procedures are known to suffer from convergence problems due to negative softening stiffness, bifurcations and snap-backs. Explicit techniques have the potential to overcome those, but examples are rather scarce. In this study a popular

Fatigue fracture behaviour of concrete through wedge-splitting tests

Fracture in concrete takes place at pre-existing crack tip when a fracture process zone (FPZ) with a number of toughening mechanisms is formed. In order to continually monitor and gain insight into the progression of cracks and its behaviour in concrete, notched wedge-splitting specimens are experimentally investigated under crack opening to examine the fracture and

Predicting the rate of fatigue crack propagation in concrete using acoustic emission

Acousticemission(AE)isanon-destructivetestingtechniquethatcanbeusedforreal-time monitoring and quantification of fatigue crack growth in concrete structures. This can be achieved by establishing correlations between the rate of crack propagation and acoustic emission signal char- acteristics. The aim of the present work is to extract multiple AE parameters such as hits, counts, amplitude, and energy from AE signals and subsequently, identify

Do you want to boost your business today?

This is your chance to invite visitors to contact you. Tell them you’ll be happy to answer all their questions as soon as possible.